How To Change The Front Wheel Bearings On Your Dirt Bike

Oct 18, 2017

How To Replace Your Front Wheel Bearings And Service The Hub

Replacing the front wheel bearings on your dirt bike is a fairly easy repair. The bearings are a press fit, so you will need a torch and patience to remove them.

The Tools You Will Need To Replace Your Front Wheel Bearings

A long drift
Tire Spoon
Aftermarket hammer
Stock hammer
A socket that matches the OUTSIDE bearing race diameter
A socket that matches the INSIDE bearing race diameter
Socket wrench extension
Propane torch
Two long 2x4s
A small block of wood
Rubber Gloves
Work Gloves
Eye protection

The Parts You Will Need

The parts you will need are a set of new bearings and seals, and a bucket of grease.

I will be installing a new set of Factory Links bearings and seals.

These bearings come pre-greased and double shielded, and the seals are reinforced with an internal tension spring.

I highly recommend this Factory links bearing and seal set, and they go for around $20 You HERE if you don’t have yours yet. (It looks like those bearings are unavailable right now)

The grease I will be using is general-purpose automotive grease, and you can get yours anywhere.

You Can Get Parts And Tools Through Our Partner Links HERE!

It always helps to know what you’re working on before you work on it, so make sure to learn how your front hub works before you start on the bearings.

Unlike the rear wheel, you can start with either side of the front wheel hub. In this guide, I will be starting with the left bearing.

Front Wheel Bearing Removal

Pry out the old seals.
- There is usually a small lip inside the seal. Hook this lip with your tire spoon to pry it out.
Dislodge the distance collar.
Insert your drift from the right side of the hub up to, but not touching, the left bearing.
Work your drift around to push the distance collar away from the inner bearing race.
Find a sturdy surface. You will be hammering your bearings out, so make sure you are on a sturdy surface. Floors usually work.
Place your wheel on your 2x4s with the left bearing facing UP.
Make sure the rim and tire are the only part of the wheel touching wood.

Step 1 - Pry Out The Old Bearing Seals — Step 1 – Pry Out The Old Bearing Seals

Step 2 - Insert Your Drift Into Hub — Step 2 – Insert Your Drift Into Hub

Step 3 - Dislidge The Distance Collar — Step 3 – Dislidge The Distance Collar

Step 4 - Place Your Wheel On 2x4s — Step 4 – Place Your Wheel On 2x4s

Remove The First Bearing

Heat the hub with your propane torch. This will let your hub expand slightly and take some pressure off of the bearing.
Move your torch around the hub, keeping the heat even as you go.
Heat the hub for around 60 Mississippi.
Flip your wheel over, and place a socket over the INNER bearing race, and hammer (tap) the opposite bearing out.
Your bearings may come out in one piece, or they might shatter as this one did.
If the other bearing is still intact, repeat the heat and beat process.

Step 5 - Heat The Hub Bore — Step 5 – Heat The Hub Bore

Step 5.1 - Heat For 60 Mississippi — Step 5.1 – Heat For 60 Mississippi

Step 6 - Tap The Old Out Bearing — Step 6 – Tap The Old Out Bearing

Front Wheel Bearings - Old Bearings On Towel - Closeup on Shattered Bearing — This Is What Shattered Bearings Look Like

Step 7 - Repeat On The Opposite Side — Step 7 – Repeat On The Opposite Side

Front Wheel Hub Maintenance

Inspect every part of the hub assembly for excessive wear, pits, and burs. If you find any rough areas, file them down to smooth.
DO NOT remove material from the ends of the distance collars.
- These parts need to stay an exact length. If the ends are damaged, replace the collar.
After you have removed any damage, sand every hub component with 220 grit sandpaper to ensure every contact surface is as clean as possible.
Take your new bearings, and make sure they DO NOT fit. These bearings are a press fit, so if they slip into the hub on their own, the hub is worn and needs to be replaced.
In this case, the left side bore is a loose fit at first, but it tightened up farther in. This will still work, but this is most likely the last bearing change for this hub.

Step 8 - File Any Pits Or Burs — Step 8 – File Any Pits Or Burs

Step 9 - Sand Ends Smooth — Step 9 – Sand Ends Smooth

Step 10 - Test Fit New Left Side Bearings — Step 10 – Test Fit New Left Side Bearings

Step 10.1 - Test Fit The New Right Side Bearings — Step 10.1 – Test Fit The New Right Side Bearings

Front Wheel Bearing Installation

If you go with single shield bearings (why), you will need to grease them before you install them, and the shielded side will need to face out.
Throughout this bearing install, you will need to grease the hub between every step.
Place your wheel on a block of wood, so only the hub is supported.
Position your bearing flush against the hub.
Use a socket that is big enough to match the OUTER bearing race, but will still fit into the bore to start tapping the bearing into place.
- Once the bearing starts to seat, make sure it is square to the bore. Adjust the bearing with light hammer taps as needed.
Drive the bearing until it is seated in the bore.
Flip your wheel and insert the distance collar.
Repeat the driving process until the top of the second bearing is flush with the bore.
Insert the axle into the opposite side of the hub to align the collar to the bearings. Make sure the axle is still tight in the collar and bearings.
Drive the bearing into the bore, then remove the axle.
If your seals contain a retaining spring, make sure it is facing in and drive your new seals until they are flush to the hub.
Remember to take your time, and your bearing replacement will be easy.